Re: 245Cm

From: francesca belloni <francesca.belloni2_at_studenti.unimi.it>
Date: Sun, 30 Aug 2009 12:42:08 +0200

Dear Alberto,
          excuse me, you're right I had to attach my input files.
I think I made something wrong 'cause I've just tried to replace HEAVY-ION with another particle ,
in order not to use SOURCE and source.f,and the run -usin 245Cm- didn't get aborted (File Prova.inp)
But I can't find the mistake. Could you please help me?

      In attachment are the input and output files.
Running 241Am.inp with source_241.f gives no problem and the files
241Am001.log and 241Am001.out are obtained (241Am001.log is cut because it
would be 29MB).
If I run 245Cm.inp with source_245.f instead the run gets aborted, but
inside the 245Cm001.log and 245Cm001.out files I find no warning.
      Thus i tried to use 241Am_mix.inp and source.f
The file 241Am_mix.inp is the same as 241Am.inp, but the dafault is
EM-CASCA instead of ICARUS. I ran the file several times, decommenting a
different material (235U, 241Am, 237Np, 245Cm,252Cf). Up to Z=95 there is
no problem,for higher Z run still gets aborted with no warning.

Thank you,
best regards,
Francesca

----- Messaggio Originale -----
Da: Alberto Fasso' <fasso_at_slac.stanford.edu>
Data: Sabato, Agosto 29, 2009 6:39 pm
Oggetto: Re: 245Cm
A: fluka-discuss_at_fluka.org
Cc: francesca belloni <francesca.belloni2_at_studenti.unimi.it>

> Dear Francesca,
>
> in your previous email you asked just
> "is it possible defining 245Cm as a material in FLUKA (EM-CASCA
> default)?". You did not attach your input file.
> I tried it on the example input which is distributed with FLUKA,
> replacing the beam particle with ELECTRON and the BERYLLIU material
> with 245Cm, and it worked. So, it is not a question of material.
> If your run is aborted, it must be for some other cause, but we
> don't have any information. Please send your input file, log file,
> *.out file and source file (if any).
>
> Regards,
>
> Alberto
>
>
>
> On Sat, 29 Aug 2009, francesca belloni wrote:
>
> > Dear Alberto,
> > thank you for your answer.
> > I generated fission fragments (HEAVY-ION card) inside
> different targets
> > (235U, 233U, 241Am...) in order to score energy deposition in
> a gas
> > located in front of the target. I usually used the ICARUS default.
> > Then I tried with 245CM in the EM-CASCA default (adding
> > DELTA-RAY,FLUKA-FIX, EVENTYPE,... cards in order to report it
> to the
> > ICARUS default, but skipping LOW-NEUT), but the run gets aborted.
> > Is there a way to reproduce FFs exiting from a 245Cm
> > target,please?
> >
> > Thank you,
> > best regards,
> > Francesca Belloni
> >
> >
> > ----- Messaggio Originale -----
> > Da: Alberto Fasso' <fasso_at_slac.stanford.edu>
> > Data: Venerdi', Agosto 28, 2009 9:10 pm
> > Oggetto: Re: 245Cm
> > A: fluka-discuss_at_fluka.org
> > Cc: francesca belloni <francesca.belloni2_at_studenti.unimi.it>
> >
> > > Cara Francesca,
> > >
> > > yes, with EM-CASCA it is possible. Just define the material:
> > > MATERIAL
> > > 96.0 245.00
> > > 13.5 0.0 0.0 0.0 CM245
> > >
> > > With other DEFAULTS, you should be more careful, since there
> is no
> > > low-energy neutron cross section available. But pure
> electron-photon
> > > interactions can be simulated up to Z=100.
> > >
> > > Alberto
> > >
> > >
> > >
> > > On Thu, 27 Aug 2009, francesca belloni wrote:
> > >
> > > > Dear all
> > > >
> > > > is it possible defining 245Cm as a material in FLUKA (EM-CASCA
> > > default)> please
> > > >
> > > > Thank you
> > > >
> > > > best regards
> > > >
> > > > Francesca Belloni
> > > >
> > > >
> > >
> > > --
> > > Alberto Fasso`
> > > SLAC-RP, MS 48, 2575 Sand Hill Road, Menlo Park CA 94025
> > > Phone: (1 650) 926 4762 Fax: (1 650) 926 3569
> > > fasso_at_slac.stanford.edu
> > >
> >
>
> --
> Alberto Fasso`
> SLAC-RP, MS 48, 2575 Sand Hill Road, Menlo Park CA 94025
> Phone: (1 650) 926 4762 Fax: (1 650) 926 3569
> fasso_at_slac.stanford.edu
>

Received on Sun Aug 30 2009 - 14:06:28 CEST

This archive was generated by hypermail 2.2.0 : Sun Aug 30 2009 - 14:06:29 CEST