Dear Maura,
To go back to your original question about importing CAD files into FLUKA, the answer is no: there is no direct importing of CAD into FLUKA. FluDAG is a software package that allows you to run FLUKA directly on CAD models. The earlier thread contained this link to NIM paper describing FluDAG development
https://doi.org/10.1016/j.nima.2018.10.117
<
https://doi.org/10.1016/j.nima.2018.10.117>
Best regards,
George
________________________________
From: Maura Monville <mm01886_at_surrey.ac.uk>
Sent: Friday, May 24, 2019 10:18:42 PM
To: George Kharashvili; fluka-discuss_at_fluka.org
Subject: Re: An old question revisited
Thank you.
I read the message. I don't quite understand if FluDAG is another Monte Carlo package that uses Fluka as its engine or it is a new Fluka version, or it is a Fluka extension.
Where can I find out about FluDAG?
Best regards,
Maura E. M
________________________________
From: George Kharashvili <georgek_at_jlab.org>
Sent: Friday, May 24, 2019 18:23
To: Monville, Maura (PG/T - Physics); fluka-discuss_at_fluka.org
Subject: Re: An old question revisited
Dear Maura,
Check out FluDAG. Reference was posted here several months ago
http://www.fluka.org/web_archive/earchive/new-fluka-discuss/13101.html<
https://urldefense.proofpoint.com/v2/url?u=https-3A__eur02.safelinks.protection.outlook.com_-3Furl-3Dhttp-253A-252F-252Fwww.fluka.org-252Fweb-5Farchive-252Fearchive-252Fnew-2Dfluka-2Ddiscuss-252F13101.html-26data-3D02-257C01-257Cmm01886-2540surrey.ac.uk-257C5d0b0c344e084a50667108d6e06c88a4-257C6b902693107440aa9e21d89446a2ebb5-257C0-257C1-257C636943154131552926-26sdata-3D-252FVjIwAGZeWxVrC-252BnvhouuzxiqOjaCen0zbbG-252FlNSRzQ-253D-26reserved-3D0&d=DwMFAw&c=CJqEzB1piLOyyvZjb8YUQw&r=wnhwhiP4anjso5jEN5gUMw&m=DnsuMvcJi4r64EqMw0DLwygq_72XqaXSbXlBS9RYdb4&s=S3w_Pim7XuKhxCmfZMTPt19KA7ggumL6Ca9A8AMLEkU&e=>
Best regards,
George
________________________________
From: owner-fluka-discuss_at_mi.infn.it <owner-fluka-discuss_at_mi.infn.it> on behalf of Maura Monville <mm01886_at_surrey.ac.uk>
Sent: Friday, May 24, 2019 6:17:13 PM
To: fluka-discuss_at_fluka.org
Subject: [fluka-discuss]: An old question revisited
Dear Fluka experts,
I found an old email, dated 2016, which is dealing with a topic I am interested in.
The email inquired about the possibility of importing CAD files into a Fluka model.
Such a feature is available from Geant4, Topas. Maybe also from MCNPX but I am not 100% sure about it.
In 2016 the answer was negative .
I wonder whether in the meantime something has changed about Fluka.
Has it been modernized at all?
Thank you.
Best regards,
maura E. M.
__________________________________________________________________________
You can manage unsubscription from this mailing list at
https://www.fluka.org/fluka.php?id=acc_info
Received on Sat May 25 2019 - 11:36:35 CEST